विवरण
हांग्ज़ौ एवर-पावर स्प्रोकेट कंपनी लिमिटेड
When a #40 SS drive is running at its limit, engineers face two routes: add a second strand (duplex), or move up to #50 pitch. Each has a different cost and complexity profile. This page explains how to choose between them.
Two Routes When Your #40 Drive Is Overloaded
An ANSI 40 single-strand drive can handle approximately 14 kN maximum chain tension under moderate-speed operation. When process changes push the drive beyond that ceiling — higher throughput, heavier product, faster conveyor speed — the chain elongates faster than the replacement schedule allows, and sprocket tooth tips begin to round under the excess load. At that point, the engineering team has a genuine decision to make: convert to 40-2 duplex (adding a second strand of #40 chain, roughly doubling power capacity) or upgrade to #50 pitch (larger chain, single strand, ~60% more capacity). Neither answer is universally correct. The choice depends on shaft centre distance flexibility, available sprocket hub width, and how much capacity headroom the drive needs going forward.
Single-Strand #50 vs. Duplex #40 — The Engineering Trade-Offs
| Factor | #50 Single Strand | #40 Duplex (40-2) |
|---|---|---|
| Capacity vs #40 single | ~60% more tension | ~90% more tension |
| Sprocket width | Single row — narrower | Double row — wider hub needed |
| Centre-to-centre change | May require adjustment | Usually stays same |
| Drive alignment sensitivity | मानक | More critical — both strands must load equally |
| Chain cost | ~1.3× #40 single | ~2× #40 single |
| Best when | 60% uplift is enough; hub width is limited | Near-double capacity needed; centres fixed |
तकनीकी निर्देश
| पैरामीटर | कीमत |
|---|---|
| चेन नंबर | एएनएसआई 50 |
| आवाज़ का उतार-चढ़ाव | 15.875 मिमी (5/8″) |
| रोलर व्यास | 10.16 मिमी |
| आंतरिक चौड़ाई | 9.53 मिमी |
| सामग्री | 304 एसएस / 316 एसएस |
| दांतों की सीमा | 9T – 80T |
| अनुपालन | एएनएसआई बी29.1, आईएसओ 9001:2015 |
Drive Sizing: Speed Ratio and Tooth Count Selection for #50
Good drive design for #50 pitch follows the same principles as any roller chain drive, with a few specific recommendations that extend service life in SS food-grade applications:
Minimum 17T for smooth chain engagement. 19T or 21T (odd counts) gives even wear distribution across all chain links — recommended for long-interval food applications.
Keep single-stage ratio at or below 7:1. Above this, a two-stage reduction is more efficient — it reduces the load on the slow-speed chain strand and extends both chain and स्प्रोकेट life.
30–50 pitches of centre distance is the practical optimum. This gives adequate chain wrap on the driver (≥ 120°) and a chain sag that self-tensions without over-stressing the bearings.
Components for a Complete #50 SS Drive
Whether you are building a new #50 drive or upgrading from a #40 system, we supply the complete component set so every part of your स्टेनलेस स्टील स्प्रोकेट drive is grade-consistent:
- एएनएसआई 50 एसएस रोलर चेन — 304 and 316, single-strand and 50-2 duplex
- एसएस आइडलर स्प्रोकेट — for tensioning and slack-side guidance
- एनएसएफ एच1 खाद्य-श्रेणी स्नेहक — drip oil or PTFE spray, compatible with SS chain
- टेपर-लॉक बुशिंग सेट — for planned changeout without shaft disassembly
- Complete Drive Calculation Service — send your power, speed, and shaft data and we calculate tooth counts, chain length, and component selection
ग्राहक समीक्षाएँ
“The engineering team chose single-strand #50 over 40-2 duplex based on hub-width constraints. Ever-Power supplied matched SS sprockets and chain — the drive has run without issues for 14 months in our tunnel washer application.”
“We asked Ever-Power to do the drive calculation from our motor data. They came back with tooth counts, chain length, and a taper-lock bushing recommendation. Everything fitted as calculated on the first installation.”
“Good quality product, delivered on time. A stocked range of the most common 17T and 19T configurations would be useful for emergency orders — currently everything is made to order.”
Send Your Drive Data — We Size the System
Power (kW), input speed (RPM), output speed (RPM), shaft diameters. We’ll return tooth counts, chain length, and pricing within 24 hours.
+86-571-88220653 | [email protected]
हमारे बारे में और जानें बड़े स्प्रोकेट रेंज या हमारी कंपनी के बारे में और अधिक जानने के लिए संपर्क पृष्ठ.
समीक्षा
अभी तक कोई समीक्षा नहीं।